W Series

Oil Burner

All W Series Weishaupt Burner use the latest microprocessor technology for the control and monitoring of all the burner functions. As a result not only do they offer improved precision and ease of use but they also represent fantastic value for money.

WL 5 16.5 - 55 KW

WL10 to WL40 30 - 570 KW

• Economy through digital technology
• Fully automatic operation
• Compact construction
• Operational safety and reliability.
• Error free plug connection

Standard execution burners are suited for a diverse range of heat exchangers as well as, for example, air heaters.

Monarch

Oil Burner

Weishaupt Monarch oil burners are of the fully automatic pressure atomizing type. Their design has been carefully considered down to the smallest detail and has been proved successful over and over again. They meet all the demands for safety, reliability and low cost servicing. Weishaupt oil burners are type tested to EN 267.

Size 1 - 3 70 - 775 KW

Size 5 - 11 180 - 5540 KW

• Automatic sequence of operations
• Stable fan characteristics – good combustion results
• Air regulation on pressure side
• Air damper closed on burner shutdown
• Quiet operation
• Complete pre-wired integral switchgear
• Hinged burner casing
• Combustion head can be withdrawn when the burner is hinged open
• The design of the burner makes installation, adjustment and servicing easy

On L , M and MS type burners, the regulation of oil and air takes place as follows:

• Two stage, nozzle head with two nozzles and a motor controlled, quickly opening air damper.
• Three stage, with three nozzles and a motor controlled, slowly opening air damper.

The RL and RMS burners, Fuel and air are controlled in compound. The burner can, depending on the controller and servomotor, be either:

• Sliding two stage (20 s running time) or Modulating (42 s running time)

The burners can be used on hot water boilers, steam boilers, air heaters and for certain heating processes. The burners are used in particular on modern, high rated boilers, as they are capable of overcoming high combustion chamber pressures. RL and RMS burners are preferably used where there is a continually changing heat demand.

Industrial

Oil Burner

Weishaupt industrial burners, sizes 30 to 70, have been especially designed for industrial capacity ranges. The monobloc burners are noteworthy for their large capacity and operational ranges

Size 30 - 70 475 - 8750 KW

• Compliance with the most stringent directives and emission limits
• Large capacity and operational ranges
• Stable fan reference line - good combustion behaviour
• Quiet operation
• Burner housing can be hinged open
• Easy to install, set and service
• Automatic air shut off on burner shut down

Dependent on fuel, burner size and requirements, the regulation of air and fuel is by:

• Two and three stage -- Oil burners have a nozzle assemble with two or three nozzles. A change in firing rate is effected by opening and closing of solenoid valves 2 and 3 with the relevant air volume.
• Two and three stage -- For sliding two stage control, partial and full load are set positions within the regulation range. The burners firing rate slides between the two load points, depending on the heat demand. Thus there are no sudden large increases or decreases in the amount of fuel used.
• Modulation Modulating burners operate at any point within the regulation range, depending on the heat demand.

The burners can be used on hot water boilers, steam boilers, air heaters and for certain heating processes. The burners are used in particular on modern, high rated boilers, as they are capable of overcoming high combustion chamber pressures. RL burners are preferably used where there is a continually changing heat demand.

WM Series

Oil Burner

Weishaupt WM Series oil burners are equipped as standard with electronic compound regulation and digital combustion management. Modern combustion technologies demand a precise, continually reproducible dosing of fuel and combustion air. Only in this way can optimal combustion figures be ensured over extended periods

WM - L10 75 - 1120KW
WM - L20 400 – 2600 KW

• Digital Combustion management with electronics compound regulation at all ratings
• More compact that previous burners a similar rating
• Sound attenuated air inlet as standard for quieter operation
• Powerful fan due to the specially developed fan geometry and air damper control
• Oil Burners are delivered with Oil nozzles fitted and the mixing assembly preset for the required output of the burner
• IP 54 Protection as standard
• Easy access to all components, such as oil nozzles, air damper and combustion manager
• Safe operation with 3 stage (depending on the type of capacity on the type of capacity regulation) sliding 2 stage / modulating operation as standard
• Computer controlled function test at the factory of each individual burner
• Burner can be supplied pre-wired with plug connections
• Excellent price / capacity ratio

Dependent on fuel, burner size and requirements, the regulation of air and fuel is by:

• Two and three stage -- Oil burners have a nozzle assemble with two or three nozzles. A change in firing rate is effected by opening and closing of solenoid valves 2 and 3 with the relevant air volume.
• Two and three stage -- For sliding two stage control, partial and full load are set positions within the regulation range. The burners firing rate slides between the two load points, depending on the heat demand. Thus there are no sudden large increases or decreases in the amount of fuel used.
• Modulation Modulating burners operate at any point within the regulation range, depending on the heat demand.

The Weishaupt WM series oil burners are tested to EN 267 and suitable for Heat exchangers, hot water plant, Steam boilers and high pressure hot water plant, Air Heaters.